Manual freewheels AVM 411, set of 2, allow on selected 4x4 vehicles to manually connect or disconnect the front wheels from the half-shafts, ensure transfer of driving force in 4x4 mode and reduce unnecessary spinning of the front drivetrain when…
A set of 2 manual freewheels AVM 411 serves as detachable freewheel hubs for the front wheels on selected 4x4 and off-road vehicles. When manually engaged, the hub connects the wheel hub to the front axle half-shaft, allowing driving force to be transmitted to the front wheels when four-wheel drive is engaged. When disengaged, the front wheels rotate freely during 4x2 driving without unnecessarily spinning parts of the front drivetrain, which helps reduce mechanical resistance and wear. The freewheels complement the vehicle's 4x4 control and do not replace the vehicle's own 4x4 engagement. Robust steel construction protected by epoxy paint increases resistance to environmental effects, and precisely machined internal components support reliable operation in normal use as well as in more demanding off-road conditions.
Bonjour,Je suis un garage, je suis entrain de réparer un aro 10 "Green City" de octobre 1996.Moteur renault 1,9 Diesel
Hello,I run a garage; I'm currently repairing an ARO 10 "Green City" from October 1996.Renault 1.9 diesel engine.
Bruno, 15. 01. 2026
Original message in
Bonjour, merci pour votre demande.La roue libre AVM 411 est indiquée sur notre site comme compatible avec les véhicules ARO (A10), Ischia (à partir de 1981) et Santana.Pour confirmer la compatibilité, il faut vérifier les paramètres de montage : 22 cannelures (splines) côté arbre, fixation par 6 vis et PCD 99 mm.Si votre ARO 10 (1996) correspond à ces valeurs (22 cannelures / 6 vis / PCD 99 mm), la roue libre sera compatible. Si ces valeurs diffèrent, nous ne pouvons pas confirmer la compatibilité.
Hello, thank you for your inquiry.The AVM 411 freewheel is listed on our site as compatible with ARO (A10), Ischia (from 1981) and Santana vehicles. To confirm compatibility, you must check the mounting parameters: 22 splines on the shaft side, attachment with 6 bolts and PCD 99 mm.If your ARO 10 (1996) matches these values (22 splines / 6 bolts / PCD 99 mm), the freewheel will be compatible. If these values differ, we cannot confirm compatibility.
Hello.Would this product be suitable for my 2018 Suzuki Vitara equipped with a fixed, precise connector? It’s the GL trim.
László, 14. 06. 2026
Hello, we don't know individual cars. Please select according to the file at this link.https://www.sixtol.hu/files/products_files/h/Hogyan_valasszunk_SIXTOL_keresztrudat_HU.pdfThank you
Dear Sir or Madam,I am interested in your AVM 455HP High Performance Freilaufnaben (the reinforced, high-load-capacity version — not the standard version) for my Toyota.Please check whether the AVM 455HP High Performance Freilaufnaben are suitable for my vehicle.Vehicle data:Toyota Land Cruiser Pick-up Single CabModel: GRJ79Year of manufacture: 2022Engine: 4.0 V6 petrol (1GR-FE)Manual…
Hedi, 26. 07. 2026
Yes. For the Toyota Land Cruiser GRJ79 Single Cab (70 series, from 7/2009 including model year 2022) the AVM 455 is the correct freewheel model.Have a nice day
Good day, I would like to ask whether the listed fastening straps are also produced in a longer length; I would need 35 cm.Thank you.
Michal, 14. 08. 2026
Hello,we unfortunately do not have the same type of fastening strap in 35 cm length available. The closest similar variant we offer is SX1014E – quick-release strap for a towbar-mounted bike carrier, length 38 cm, black.However, this strap has slightly larger dimensions and a different attachment method, so we recommend verifying before purchase whether it will be suitable for your intended…
Hello! will this fit my 2005 Nissan D22 Manual transmission? and is this all i need for getting a manuel hub to work on my car.To day there is an atomactic hub. Do you ship to Norway.Thank you. Halvard
Halvard, 22. 08. 2026
For the Nissan D22 2005 4×4, the AVM 461HP is the correct type and normally no special adapter should be required. Before installation, however, I would definitely verify the 28 splines + 6× M8 + PCD 83 mm and the method of securing the half-shaft with a circlip. We also ship to Norway. Have a nice day.
Hello, this product has already been ordered, but the shipment containing these goods will not arrive until approximately the beginning of October. Have a nice day.
Hello,Could you send me the user manual for the buttons inside the helmet?Kind regards,Sophie PÉRIER.
Sophie, 22. 01. 2026
Hello Madame PÉRIER,Thank you for your message. Here is the link to the document to download: https://www.sixtol.fr/casque-de-soudage-auto-obscurcissant-welding-mask-2-rouge.html#tab-documentsTo help you quickly, here is a summary of the controls inside the helmet:• Knob “Delay”: adjusts the time to return to the clear state after welding.• Knob “Sensitivity”: adjusts the filter sensitivity…
Hello, which rubber pads are compatible with this jack, please? Is this new model in any way better or worse than the previous heave-duty SX JACK 3T, aside from the pedal mechanism? Thanks.
Marek, 03. 10. 2026
Hello, it matches the JACK PAD 10 with code SX306403 exactly in dimensions. In addition to the foot pedal it has a tray for screws and nuts and a lift of up to 505 mm. Have a nice day.