The mats are manufactured precisely according to the shape of the floor areas of the specific vehicle type. This eliminates the need for difficult comparisons of often inaccurate universal mats and the problematic trimming to the required shape.
Usage
The mats are easy to wash, allow quick emptying of dirt and are easy to install.
Material
Highly durable rubber provides the mats with high elasticity, ensuring that when bent (e.g. during storage) the mats will return to their original shape.
Protection
The advantage of these mats is a raised edge that protects the vehicle interior from the spilling of granular materials (sand, soil) or the pouring of liquids (water), dirt, dust, snow, etc. into the vehicle interior, and which is resistant to penetration by oils, petrol and partially by battery electrolyte.
Comfort
Unpleasant shifting of the mats on the vehicle floor or bunching under the pedals is effectively prevented by a special non-slip profiling on the underside of the mats, which easily attaches to the original floor upholstery.
Maintenance
The mats are easy to wash, adapted for standard maintenance using common cleaning agents (e.g. washing with lukewarm water and a non-aggressive, non-abrasive detergent, etc.). Cleaning can be easily carried out outside the vehicle. Regular emptying of dirt is also simple and can be done in a few seconds.
Hello, can I transport 2 e-bikes and 2 children's bikes with this carrier? The children's bikes are one 16-inch and one 20-inch. Thank you in advance for a prompt reply.Kind regards
M, 28. 03. 2026
Hello,this rack is primarily intended for transporting 4 conventional bicycles, not e-bikes, mainly due to their higher weight.In the case of a combination of 2 e-bikes and 2 children's bikes, you must thoroughly check the total weight of all bikes. The rack's maximum load capacity is 60 kg and this value cannot be exceeded.We therefore recommend considering transporting the children's…
Good morning, I wanted to know whether the AVM406HP freewheel coupling would be suitable for an Iveco Massif. Thank you
Salvatore, 23. 03. 2026
Hello,thank you for your inquiry. According to AVM's application table, the model AVM 406MI is listed for the Iveco Massif. For the product AVM406HP we currently have inconsistent information on the website, so we cannot confirm its suitability for the Iveco Massif 100% at this time.To give you an exact answer, we recommend verifying compatibility by VIN / exact year of manufacture and type of…
Hello,Could you send me the user manual for the buttons inside the helmet?Kind regards,Sophie PÉRIER.
Sophie, 22. 01. 2026
Hello Madame PÉRIER,Thank you for your message. Here is the link to the document to download: https://www.sixtol.fr/casque-de-soudage-auto-obscurcissant-welding-mask-2-rouge.html#tab-documentsTo help you quickly, here is a summary of the controls inside the helmet:• Knob “Delay”: adjusts the time to return to the clear state after welding.• Knob “Sensitivity”: adjusts the filter sensitivity…
Good morning, my name is Fernando Montero.I am writing to ask whether it would be possible to purchase the rails on which the bicycle wheels rest for your e-bike rack model (SX1014).Thank you very much for your attention.Regards.
Fernando, 01. 12. 2025
Hello, yes, that is possible. We can send it to you from our service center. Please write to us at info@sixtol.com and we will take care of it.
Hello, which specific type of expander for the cup holder should I order for this original cup holder in the Kodiaq (the opening only fits a standard can)…
Karel, 15. 03. 2026
Hello Mr. Bárta,thank you for your inquiry.For the original cup holder in the Škoda Kodiaq you mentioned, we recommend using the SIXTOL CAR CUP HOLDER 5 model.This expander has an adjustable lower base ranging from 6.5 to 10 cm, so it will adapt even to smaller original holders (a standard can has a diameter of 6.5 cm). At the same time it has a top diameter of approximately 9.6 cm, which…
Hello,I would like to ask whether a load-distributing pad that fits between the jack and the car can be purchased for the Hydraulický zdvihák fľaškový SX BOTTLE JACK 4T.Or which jack would you recommend for a Mercedes‑Benz V‑Class?Thank you for your reply.Miroslav Hanzen
Miroslav, 28. 01. 2026
Hello, pán Hanzen,thank you for your inquiry. We don't have an original "load-distributing pad" for the SX BOTTLE JACK 4T (SX1146), but you can use a standard rubber pad/adapter for the jack (jack pad) between the jack and the vehicle's jacking point. For the Mercedes-Benz V‑Class the 4T capacity is fine; what's important is that the jack's minimum height (when lowered) fits under the car. If…